Celestia crash at startup on Linux
Posted: 24.06.2003, 02:06
My system:
Linux 2.4.20-xfs #1 SMP Die Dez 10 20:07:25 CET 2002 i686 AMD Duron(tm) processor AuthenticAMD GNU/Linux
My videocard:
VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
X-window: XFree86 version 4.2.1.1
KDE version 3.1.2
I compiled the Celestia 1.3.0 version for Linux following
this directives:
./configure --with-qt-dir=/usr/share/qt3/ --with-kde
After issuing: make;make install
and running the program I receive the following error:
Parent body 'BD -10 3166' of 'b' not found.
fv: 6
The program 'celestia' received an X Window System error.
This probably reflects a bug in the program.
The error was 'BadMatch (invalid parameter attributes)'.
(Details: serial 193 error_code 8 request_code 144 minor_code 5)
(Note to programmers: normally, X errors are reported asynchronously;
that is, you will receive the error a while after causing it.
To debug your program, run it with the --sync command line
option to change this behavior. You can then get a meaningful
backtrace from your debugger if you break on the gdk_x_error() function.)
and these are the last lines shown inside 'gdb':
Id 'kde2.2/r2' was already in done-list!
Id 'kde2.2/r3' was already in done-list!
Running script 'kicker-3.1-properSizeSetting.pl'
Script: Writing entries to /tmp/kde-root/kconf_update7cndhb.tmp
Script: Filtered entries written to /tmp/kde-root/kconf_updatexYK1kc.tmp
Write Size -> 4
Id 'kde2.2/b1' was already in done-list!
Write ViewMenuBar -> false
Remove Key 'General'/'ViewToolBar'
Id '25082001' was already in done-list!
Running script 'klipper-kde31.sh'
Script: Writing entries to /tmp/kde-root/kconf_updatexV7Cea.tmp
Script: Filtered entries written to /tmp/kde-root/kconf_updateO6TFob.tmp
Write AutoStart -> true
Id 'kde3' was already in done-list!
(no debugging symbols found)...(no debugging symbols found)...
ERROR: KUniqueApplication: Registering failed!
ERROR: Communication problem with celestia, it probably crashed.
(no debugging symbols found)...
Program received signal SIGSEGV, Segmentation fault.
[Switching to Thread 16384 (LWP 12235)]
I will be grateful for any help on this subject or any clues to resolve the problem.
Juan[/i]
Linux 2.4.20-xfs #1 SMP Die Dez 10 20:07:25 CET 2002 i686 AMD Duron(tm) processor AuthenticAMD GNU/Linux
My videocard:
VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
X-window: XFree86 version 4.2.1.1
KDE version 3.1.2
I compiled the Celestia 1.3.0 version for Linux following
this directives:
./configure --with-qt-dir=/usr/share/qt3/ --with-kde
After issuing: make;make install
and running the program I receive the following error:
Parent body 'BD -10 3166' of 'b' not found.
fv: 6
The program 'celestia' received an X Window System error.
This probably reflects a bug in the program.
The error was 'BadMatch (invalid parameter attributes)'.
(Details: serial 193 error_code 8 request_code 144 minor_code 5)
(Note to programmers: normally, X errors are reported asynchronously;
that is, you will receive the error a while after causing it.
To debug your program, run it with the --sync command line
option to change this behavior. You can then get a meaningful
backtrace from your debugger if you break on the gdk_x_error() function.)
and these are the last lines shown inside 'gdb':
Id 'kde2.2/r2' was already in done-list!
Id 'kde2.2/r3' was already in done-list!
Running script 'kicker-3.1-properSizeSetting.pl'
Script: Writing entries to /tmp/kde-root/kconf_update7cndhb.tmp
Script: Filtered entries written to /tmp/kde-root/kconf_updatexYK1kc.tmp
Write Size -> 4
Id 'kde2.2/b1' was already in done-list!
Write ViewMenuBar -> false
Remove Key 'General'/'ViewToolBar'
Id '25082001' was already in done-list!
Running script 'klipper-kde31.sh'
Script: Writing entries to /tmp/kde-root/kconf_updatexV7Cea.tmp
Script: Filtered entries written to /tmp/kde-root/kconf_updateO6TFob.tmp
Write AutoStart -> true
Id 'kde3' was already in done-list!
(no debugging symbols found)...(no debugging symbols found)...
ERROR: KUniqueApplication: Registering failed!
ERROR: Communication problem with celestia, it probably crashed.
(no debugging symbols found)...
Program received signal SIGSEGV, Segmentation fault.
[Switching to Thread 16384 (LWP 12235)]
I will be grateful for any help on this subject or any clues to resolve the problem.
Juan[/i]